ThermaFlow DTX Physical Properties


1.04 - 1.15 g/cm³


7.5 - 10.5 depending on inhibitors

Boiling Point:



a clear, slightly viscous liquid. It is mildly sweet to the taste and has a non-pungent but characteristic aroma.

Available in:

5, 10, 15, 20, 25, 205 & 1000 litre containers and bulk tankers.


For a quote or assistance

Tel: (021) 385 0908

High Efficiency Non-Toxic Heat Transfer Fluid with Antifreeze. Based on Ethylene Glycol blended with patented DeTox™ additive with BS6580 & ASTM D1384 High Temperature Rated Corrosion Inhibitors for use in Hot Water Heating Systems.

ThermaFlow DTX has been especially formulated for use in Hot Water Heating Systems to exploit the advantages Ethylene Glycol has over Propylene Glycol, whilst delivering a non-toxic solution. Specifically;

Antifreeze AntiFreeze

ThermaFlow DTX is miscible with water in all proportions and can protect Hot Water Heating Systems systems down to -50°C depending on concentration.

non toxic Non-Toxic

Although based on Ethylene Glycol, ThermaFlow DTX has been tested and classified as Non-Toxic by an EPA certified laboratory. Previously Propylene Glycol was the only non-toxic glycol available, that is no longer the case. Hydratech in alliance with Evans Cooling Systems, Inc. have developed and patented the DeTox® additive. DeTox® prevents Ethylene Glycol from being metabolised (during digestion) into toxic by-products, which cause kidney failure, blindness and death. Tests carried out on ThermaFlow DTX confirmed the toxicity was "so low that it was impossible to determine an LD50 value".

The DeTox® additive has very little effect on heat transfer or antifreeze performance. In fact similar volumes of ThermaFlow DTX or Ethylene Glycol are required to achieve a specific freeze protection.

Optimum Flow Optimum Flow

ThermaFlow DTX has improved heat transfer characteristics. Including lower Dynamic Viscosity and higher Thermal Conductivity. For detailed comparison please refer to the Fluid Performance Chart - available upon request.

Corrosion control Corrosion Control

ThermaFlow DTX contains synergistic corrosion inhibitors to protect metals commonly found in such systems. It has been independently tested and found to meet BS6580 and ASTM D1384 corrosion standards. ThermaFlow DTX also contains scale and biological inhibitors to help prevent fouling – thus promoting long operational life and high thermal efficiency.

Biodegradable Biodegradable

ThermaFlow DTX mixtures are readily biodegradable (90% over ten days) and will not remain in the environment or bio-accumulate.

Quality Assured Quality Assured

All Hydratech products are manufactured in accordance with certified ISO9001-2008 procedures


As per BSRIA guide BG 29/2012 all pipe-work systems should be clean and free from biological contamination and debris prior to commissioning.

To minimise corrosion air ingress should be minimized. A pressurised system is best.

├»┬╗┬┐Determine the total system volume and add ThermaFlow DTX to the system according to the minimum operating temperature required (see table). The minimum dose of ThermaFlow DTX should not be less than 22% of the system volume and the maximum does not normally exceed 60%. We recommend the use of deionised, distilled or UltraPure™ water for this dilution. Avoid water containing high levels of calcium salts or Chlorides [Cl-].

Health & Safety: Please refer to the associated Safety Data Sheet. Available via Login or upon request.

Shelf Life: >3 years when stored in sealed containers out of direct sunlight.

Available in: 5, 10, 15, 20, 25, 205 & 1000 litre containers and bulk tankers.

ThermaFlow DTX can be supplied as a Ready-To-Use solution.

Mixing Guide

Frost Protection °C v/v of ThermaFlow DTX Refractive Index
-10 22% 1.356
-15 28% 1.362
-20 33% 1.367
-25 38% 1.372
-30 42% 1.376
-35 46% 1.380

When measuring the percentage of ThermaFlow DTX in the system use a refractometer

back to all ThermaFlow fluids