Please choose your preferred language

For a quote or assistance

Tel: +44 (0) 1792 586800

Pipework Protection

Technical Information

When selecting a suitable HTF for use in cooling or heating systems great emphasis should be placed on the prevention of corrosion, scaling and biological fouling. There is little point in selecting a fluid with excellent thermal conductivity if it eats through pipes, valves, heat exchangers etc. within six months!

Common types of Corrosion;

Oxidation Corrosion in aqueous-based cooling systems is caused by oxygen dissolved in the water and mainly affects metals which do not form an impermeable oxide layer. E.g. Ferrous Oxide, aka rust, forms on the surface of carbon steel. The rate of oxidation corrosion is usually quite slow on external pipework surfaces, but much accelerated internally where fluid flow will constantly remove the oxide layer, leading to a cycle of corrosion.

Galvanic Corrosion occurs where two or more dissimilar metals are 'coupled' by emersion in a fluid - as found in heating and cooling systems. An electric potential difference is generated between metals of varying nobility. Specifically metals of a lower nobility will sacrifice themselves to metals of a higher nobility. The rate of corrosion will usually depend on how far apart the metals are on the nobility scale - see below - and the relative surface areas. The rate of corrosion will increase if the anodic (less noble) area is smaller than the cathodic (more noble) area.

    Least Noble - Anodic - Susceptible to corrosion
  1. Magnesium
  2. Magnesium Alloys
  3. Zinc Corroded Beryllium
  4. Aluminum 1100, 3003, 3004, 5052, 6053
  5. Cadmium
  6. Aluminum 2017, 2024, 2117
  7. Mild Steel 1018, Wrought Iron
  8. HSLA Steel, Cast Iron
  9. Chrome Iron (active)
  10. 430 Stainless (active)
  11. 302, 303, 321, 347, 410, 416 Stainless Steel(active)
  12. Ni-Resist
  13. 316, 317 Stainless (active)
  14. Carpenter 20Cb-3 Stainless (active)
  15. Aluminum Bronze (CA687)
  16. Hastelloy C(active) Inconel 625(active) Titanium(active)
  17. Lead/Tin Solder
  18. Lead
  19. Tin
  20. Inconel 600 (active)
  21. Nickel (active)
  22. 60% Ni 15% Cr (active)
  23. 80% Ni 20% Cr (active)
  24. Hastelloy B (active)
  25. Naval Brass (CA464), Yellow Brass (CA268)
  26. Red Brass (CA230), Admiralty Brass (CA443)
  27. Copper (CA102)
  1. Manganese Bronze(CA675), Tin Bronze(CA903, 905)
  2. 410, 416 Stainless(passive) Phosphor Bronze(CA521, 524)
  3. Silicon Bronze (CA651, 655)
  4. Nickel Silver (CA 732, 735, 745, 752, 754, 757, 765, 770, 794
  5. Cupro Nickel 90-10
  6. Cupro Nickel 80-20
  7. 430 Stainless (passive)
  8. Cupro Nickel 70-30
  9. Nickel Aluminum Bronze (CA630, 632)
  10. Monel 400, K500
  11. Silver Solder
  12. Nickel (passive)
  13. 60% Ni 15% Cr (passive)
  14. Iconel 600 (passive)
  15. 80% Ni 20% Cr (passive)
  16. Chrome Iron (passive)
  17. 302, 303, 304, 321, 347 Stainless (passive)
  18. 316, 317 Stainless (passive)
  19. Carpenter 20Cb-3 Stainless (passive), Incoloy 825 (passive)
  20. Silver
  21. Titanium (passive), Hastelloy C & C276 (passive)
  22. Graphite
  23. Zirconium
  24. Gold
  25. Platinum
  26. Most Noble - Cathodic - Not prone to corrosion

Crevice Corrosion refers to the localized attack on a metal surface at, or immediately adjacent to, the gap or crevice between two joining surfaces. The gap or crevice can be formed between two metals or a metal and non-metallic material. Outside the gap or without the gap, both metals are resistant to corrosion. The damage caused by crevice corrosion is normally confined to one metal at localised area within or close to the joining surfaces.

Pitting Corrosion is the localised corrosion of a metal surface confined to a point or small area that takes the form of cavities. Pitting corrosion is one of the most damaging forms of corrosion. The Pitting Factor is the ratio of the depth of the deepest pit resulting from corrosion divided by the average penetration as calculated from weight loss. Pitting corrosion is usually found on passive metals and alloys such aluminium alloys, stainless steels and stainless alloys when the ultra-thin passive film (oxide film) is chemically or mechanically damaged and does not immediately re-passivate. The resulting pits can become wide and shallow or narrow and deep which can rapidly perforate the wall thickness of a metal.

Corrosion Inhibition

Before reviewing the different chemical methods of preventing system corrosion, it is worth listing a few design principles that will work in conjunction with any corrosion inhibitors.

Corrosion Inhibitor formulations play a vital role in maintaining pipework systems and capital equipment. By blending together several chemicals it is often possible to achieve synergistic results - specifically where two or more chemicals work better together than in isolation. Individual manufacturers of Heat Transfer Fluids should know which formulations provide the greatest long-term protection for systems fabricated from various metals and plastics. Hydratech has extensive expertise in corrosion inhibitor technology and works with individual customers to ensure the correct fluid and inhibitor combination is selected.

Hydratech blend many different corrosion inhibitor formulations for use in cooling and heating systems. Some formulations are specifically for mixing with other antifreeze chemicals, while others can be added to 'water only' systems.

To ensure that corrosion inhibitor packages continue to provide long-term system protection, Hydratech operate the SureFlow Fluid Maintenance Program, where customers periodically send fluid samples to our laboratory for testing. Subject to the test results we will sometimes make recommendations to add additional inhibitors.